Occupational Health and Safety Archives

Workplace Risk Assessment

Workplace risk assessment is fundamental step of any workplace Safety Management System (SMS). A risk assessment is a process used to identify potential hazards and analyze what could happen if a disaster or hazard occurs.

Understanding Risk Assessment

In order to understand ‘risk’ and ultimately ‘risk assessment’ we must perhaps firstly comprehend what constitutes risk and what risk is. Why we, as humans take risks almost every day of our waking lives. We take risks at home, in the office, and certainly on our way to work in the mornings as we undergo the ‘commute’ and face the challenges inherent within.

Haimes (2009), discusses risk as an amalgamation of risk dimensions, but with a more ‘human’ understanding of a problem or ‘risk interpretation’. For example, the crusty ‘old timer’, has a subjective understanding of a system that only ‘he’ understands. To use an example of a ships’ engine, the ‘old boy’ can ‘hear’ the problem. They can almost ‘feel’ the problem, sensing the risk in its continued use as opposed to the new trainee. The new trainee approaches the problem from a ‘text book’ stance. Both individuals are aware of ‘risk’ but each approach the issue from completely different angles.

Risk as an Uncertainty Management

Power (2004), labels risk as ‘uncertainty management’. He goes on to discuss how we try to create ‘constructs’ in which we can work and live. For example, seatbelts, signage, ISO standards etc. Power (2004, p.9) states that “we cannot know the risks we face now or in the future but we must act as if we do”. This is perhaps the whole ‘crux’ of risk management and risk assessment. We ‘plan’ for an outcome, we anticipate it to a certain extent but we can never fully know what its full effect will be.

As previously mentioned, we wear seat-belts, and bikers wear helmets. Unfortunately, that that does not remove the risk of excessive speed or other motorists. We can experience a car crash, we can survive. We exit our vehicles in a state of shock but then we wander onto the motorway and are stuck by a passing vehicle whose driver’s attention has been taken up with their voyeuristic intent to see the carnage of our current situation. That momentary ‘lapse’ in their concentration dooms us. Although we have ‘planned’ for a certain risk, (a car crash), we have not planned for our own immobility or shock, nor the ignorance of outside observers.

Available Solutions

So, what can we do? How do we plan for risk and conduct adequate risk assessment. Can we remove or reduce the factors which precipitate disaster, and stop ourselves and others from for getting hurt? Hollnagel, (2008, p. 172) discuses resilience and how it requires the capacity for anticipation of risk and a management plan to be applied as risks arises. To this end, perhaps the ‘Robson Risk Management Model’ may be adequate and appropriate in this regard.

This model can be used in both a ‘personal’ concept and applied in an organisational context.

Perception of the Risk

The individual or organisation perceives that a risk may be inherent in a certain activity or action.

Risk Identification.

The risk(s) of the activity is ‘identified’ and ‘labelled’ (in the organisational context) with a ‘risk assessment’ form.

Assessing Risk

The risk is ‘assessed’ on the basis of its ‘potentiality’ and ‘gravity’. If we are competent and thoughtful driver, the likelihood that we will experience a car crash might be low, but still exist. The severity however, if we crash, might be catastrophic.

Risk Strategies

Stemming from the risk assessment above, numerous risk strategies are developed with a view to removing the risk even further. This can take the form of ‘avoidance’, transfer, retention or reduction. This is referred to as the ‘HOC’ or hierarchy of controls, and is applied as follows:

Eliminate hazard at source

Elimination of a hazardous material or method. This is a permanent solution which eliminates the offending item completely, however this may not always be a viable scenario. Some hazardous items must be used or worked with in their current state, such as ‘live’ munitions on a range.

Substitute hazard at source.

If it is possible to substitute an item. An example of which is when a military force might use ‘blank rounds’ for exercises and instruction of new entrants. This substitution completely removes the risk of ‘friendly fire’ occurring.

Isolate or enclose the hazard.

An example of this is range practices being conducted ‘only’ on certified and controlled ranges. An adequate security and signalling is there in place to prevent entry to non-firers and to inform others that a shoot is taking place. This allows for the hazard to be successfully isolated and controlled without the possibility of injury.

Engineering controls

Examples of this are the aforementioned security at ranges, flag system of notification and cordon enclosing the range.

Administrative controls

Adequate supply of qualified and experienced range managers ‘in situ’ to manage the firing, observe and enforce safety measures/controls and relieve one another for breaks throughout the day. This allows for fresh, focused and diligent staff to manage the activity.

Personal protective equipment (PPE)

The last measure is the use of the correct PPE. On range practices, shooters, range security, ‘butt party’ members (those controlling the targets) and range staff must all wear adequate PPE. PPE is in the form of a Kevlar helmet, double hearing protection and GSBA (general service body armour). This control enables an extra layer of protection in the unlikely event of a miss fire.

Risk Evaluation

Following all of the above measures, the risk is then re-evaluated in order to ascertain if it still poses the same levels of risk or if the necessary controls are adequate and appropriate to remove or reduce the threat as far as possible. However, it must always be borne in mind that the full elimination of risk is perhaps impossible as it encapsulates far too many variables (both known and unknown), such as human factors, equipment, environment and indeed the risk area itself, thus in order to live with risk we should perhaps understand that a measure of risk is ever present and ‘natural’ and may even be ‘necessary’ for our continued advancement as a species.

Online Health and Safety Training

Proactive Health and Safety training is critical to ensure a safe workplace. An effective training program can reduce the number of worker injuries and deaths. It can also reduce instances of property damage, legal liability, illnesses, and missed time from work.

Health and Safety training helps establish a culture in which employees themselves help promote proper safety procedures while on the job. It is important that new employees be properly trained and embrace the importance of workplace safety. The role of training in developing and maintaining effective hazard control activities is a proven and successful method of intervention.

This is why we have established Myelearsafety school. We pride ourselves in how we guide, support and mentor our students. They receive support throughout their learning experience and into their working lives. Our staff have extensive training experience and also have many years industry experience. We understand the challenges that exist within Environmental and Occupational Health and Safety. Our priority is to ensure that all learners are fully prepared to differentiate themselves in the workplace after completing our Health and Safety courses.

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

eLearn Online Health and Safety Training

Ergonomics in the Workplace

Ergonomics is the study of working interactions between humans and machines/workstations and the factors that affect those interactions. Stemming from the Greek words ‘ergo’ & ‘nomus’ (workflow) it is in simple terms ‘fitting’ the job to the person as opposed to fitting the person to the job.

Origins of the Ergonomics

Ergonomic practitioners draw upon a number of different disciplines. Some of these are ‘biomechanics’ (the study of human movement and the associated laws) and ‘anthropometry’ (the study of human measurements). These disciplines assist ergonomic practitioners in identifying ergonomic risk factors.

Importance of Ergonomics in the Workplace

Failure to apply the principles of ergonomics within the workplace i.e., a busy office environment or warehouse can result in chronic or acute musculoskeletal injuries. If left unchecked can result in functional limitations. Employees working in such environments are also susceptible to RSI ‘repetitive strain injuries’ and WRULD ‘work related upper limb disorders’.

When designing workstations ergonomic considerations are of significant importance. An ergonomic risk assessment can help to identify issues with existing workstations. However prior to conducting a risk assessment a task analysis should be conducted. A task analysis is conducted in order to get an appreciation of an employee’s daily routine. A task analysis will highlight current or potential issues for the employee, time spent at the work station, breaks, and shift work. All these should all be taken into consideration. In addition, biomechanics and anthropometrics will also play a part at this point.

Ergonomic Tools

Ergonomic practitioners can utilize a number of tools in order to assist them in rating the risks accordingly:

Rapid employee body assessment (REBA) tool.
Rapid upper limb assessment (RULA) tool.
Assessment of repetitive tasks (ART) tool.

In addition, eLearn Safety offers a full online VDU/DSE course. This course is fully online and can be taken 24/7. On completion of this VDU training course, participants will be provided with the information necessary to ensure current legislation is complied, risk assessments are carried out and all employees are competent to adjust their work stations to provide a safe place to work in.

Furthermore, a task analysis will help to identify if an employer is compliant with current legislation under the SHWW Act 2005. An office employees’ display screen is in essence a visual display unit. Therefore an employer must adhere to the guidance document within the general application regulations pertaining to VDU’s and display screen equipment.

Ergonomics in the Workplace Recommendations

Where office workers should be afforded the option to conduct his/her work both in the seated and standing position, employers must ensure chairs and VDU’s have the ability to be adjusted to suit all employees and consider frequent breaks and job rotation where practicable. Employers should also promote good working practices. For example, encouraging staff to make recommendations based on their working environments. If working in a warehouse or on a manufacturing line, workers should use appropriate equipment. A proper equipment will aid them in their jobs. Some of the examples are foot stools, foot rests, anti-glare eye protection, etc.

Employers should always be cognizant of the fact that ‘one shoe does not fit all’ when it comes to ergonomic assessments. For example a tall employee may feel cramped in a small area whereas a short employee may be uncomfortable if constantly reaching for items or if their feet are not supported when sitting.

Thus, structuring the working environment in order to suit the user is a step away from Taylors’ method of ‘scientific management’. Such a method, regardless of body shape and size or indeed the work being undertaken, was standardized across the board and the worker had to adapt him/herself to the factory conditions or face the prospect of dismissal and future injuries as a result.

Ergonomics Assessments

Ergonomic assessments are not difficult to undertake, and when carried out effectively can help to reduce the risk of ergonomic injuries and pain. In turn, this will help to motivate employees, allowing them to be more productive and happier in the working environment. Employers should always be aware of their responsibilities to their employees under the SHAWW Act and take the necessary steps to create risk free working environments where possible. Employees must also be aware of their rights and support any safety initiatives the employer wishes to implement, as the saying goes, ‘the rising tide floats every boat’.

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Equipment in the Workplace

Equipment in the workplace can be a cause for a serious accident. Unfortunately some of these accidents can be fatal. According to the Health and Safety Authority of Ireland (HSA) work equipment can be described as ‘any machinery, appliance, apparatus, tool or installation for use at work‘. This description is very broad and it demonstrates that the scope of work equipment is very extensive.

eLearn Safety offers a list of relevant courses that look into equipment in the workplace and its use. A solid starting course is Workplace Safety – Level 1. This course is ideal for every employee in any workplace that’s subject to Health and Safety Legislation. Safety in the workplace is everyone’s responsibility. It provides all employees who participate on this course with information on how to identify hazards and carry out simple risk assessments.

Workplace Safety – Level 1

Equipment in the Workplace and the Law

The Safety Health and Welfare at Work (General Application) Regulations, 2007 sets out the requirements with regard to equipment in the workplace. It is impossible to list all the equipment that might be used in a workplace setting, but it generally includes the following:

Plant – large fixed or mobile equipment such diggers, forklift trucks, tractors, cranes, etc.
Machinery – seemingly harmless equipment such as printer machines, cookers, but also meat slicers, band saws, circular saws, etc.
Tools – simple tools such as screwdrivers, knives, pliers, etc.

Employer and Employee Duties in Regard to Equipment in the Workplace

Both employers and employees have a number of duties under the 2005 Act in terms of equipment in the workplace. For a more comprehensive list of employer and employee duties please see HSA page titled Safety, Health and Welfare at Work Act 2005. In broad terms we can describe duties as follows:

Employers – have the responsibility to provide and maintain suitable and safe equipment in the workplace. An employer is also responsible for providing training and information on risks and precautions associated with use of the equipment in the workplace.
Employees – have the responsibility to select the suitable machine/tool for the work to be undertaken, make sure they are trained in its use and operate the machine/tool according to the safe working procedures.

Main Dangers arising from the Equipment in the Workplace

Some of the dangers of the equipment in the workplace are:

Traps and Entrapment – Moving equipment, such as presses and hydraulic jacks can trap body parts.
Contact – Abrasions, bruising or friction burns can occur when people accidentally come into contact with moving parts.
Impact – Moving parts may hit operators or the public if unguarded or badly sited.
Ejection – Some unguarded equipment, e.g. drills and saws, may throw off bits of metal or wood.
Entanglement – Moving machinery such as rollers, cogs and conveyors that can entangle hair, jewellery and clothes, even pulling whole bodies into machinery.

Controls

There are a number of controls that can be used to minimise dangers associated with the use of the equipment in the workplace. For additional information about Hierarchy of Controls, please see eLearn Safety blog entry from 24th February 2023 titled Workplace Hazards.

Guarding is often used as a method of controlling the risks associated with moving parts and machinery. Some guards act as a permanent barrier to prevent people from gaining access to a dangerous area. Other moveable types will prevent the machine from operating unless the guard is in place. It is important that guards and other safety features, such as emergency stop buttons and alarms are working correctly. If they are not, the machinery should not be used.

When selecting equipment in the workplace, it is important to choose the safest possible option for a work activity. All equipment must be CE marked and suitable for the task to be used for.

Some general rules for using any workplace equipment apply:

Select the right equipment for the right job.
Make sure the equipment is maintained and in good condition.
Report broke, damaged or worn equipment to a supervisor.
Only use equipment you have been trained to use.
Use all equipment correctly.
All equipment should be stored correctly after use.

All equipment in the workplace must be well maintained to ensure it is in safe working order. The maintenance should be carried out according to the manufacturer’s instructions by a competent person.

Equipment is only as safe as the person using it!

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Pressure and Gas at Work

Pressure and gas at work from a mains supply can be very dangerous. Gas from mains is an explosive hazard if not used correctly. In addition, poorly maintained systems can cause death from carbon monoxide poisoning. It is important to make sure anyone employed to work on gas appliances is a Registered Gas Installer (RGI). According to Gas Networks Ireland:

“A Registered Gas Installer is an installer or service engineer who has completed the required gas installation safety training, who has the necessary insurance to carry out gas installations to the legal standard and who is registered with the Register of Gas Installers of Ireland.”

You should never use an unregistered gas installer to carry out work on your gas appliances, such as gas boilers, no matter how seemingly convenient or tempting it may be. Not even if this unregistered engineer is Daniel O’Donnell.

Even if it’s Daniel – Registered Gas Installers 30 second TVC. Run time 30s.

Pressure Systems

A pressure vessel is a container that holds a liquid or gas under pressure. A pressure system is one or more such vessels including associated pipework. Examples of pressure systems include compressed air systems, boilers, steam heating systems and autoclaves. If a pressure system fails during operation it can kill or injure people in the area. In addition, a significant damage to the property can happen due to impact from the blast, debris from the explosion and fire from escaping flammable gases or liquids.

Gas Cylinders

Gas cylinders can cause the same injuries as pressure vessels should the cylinder fail or be damaged. In addition, they can cause manual handling injuries from lifting and carrying heavy cylinders and crush injuries should cylinders fail.

Basic handling precautions include:

Securing cylinders upright so they do not fall.
Keeping cylinders away from fire.
Making sure cylinders are not dropped or banged.
Moving larger cylinders with a special hand truck rather than dragging or rolling them.
Always checking the identity of the gas before using it.

The Health and Safety Authority of Ireland (HSA) has a useful information page about gas titled Liquefied Petroleum Gas (LPG) Storage.

General Pressure and Gas at Work Controls

General controls when pressure and gas at work are in question include:

Regular maintenance and correct repair from a competent person.
Safe systems of work.
Training and supervision.

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Dangers of Vibration at Work

Use of plant and equipment that produces vibration is often not considered as a serious risk and dangers of vibration at work are often overlooked.

Vibration is the transmission of force from work processes into the worker. The Health and Safety Authority of Ireland (HSA) defines vibrations as ‘rapid movement to and fro or oscillating movement‘.

Examples of Vibration at Work

People in the course of their work life may be exposed to many sources of vibration. Dangers of vibration at work are more often overlooked than not. Some vibration affects the whole body (WBV), e.g. when driving a dumper truck over rough and even ground. Here the vibration, in the form of large shocks or jolts, is transmitted to the whole body via their feet or the seat. This could cause injury to the lower back and spine.

The most common problem is Hand Arm Vibration (HAV). HAV is caused by exposure to vibration, e.g. from using hand power tools. This can be very disabling, causing severe pain in hands and arms and lack of hand movement and feeling in the fingers. It is preventable but permanent once the damage is done.

Dangers of Vibration at Work – HAV Symptoms

The most common HAV symptoms to look for are:

Tingling in the fingers.
Loss of feeling and sensation in the fingers.
Reduced strength in the hand.
Fingers that go white in the cold and then red and painful on recovery.

Dangers of Vibration at Work – HAV Controls

Dangers of vibration at work, i.e. risk from vibrating tools or machines can be minimised by:

Introducing methods that eliminate, substitute or reduce the exposure to vibration.
Avoiding prolonged or frequent use of vibrating equipment.
Keeping cutting tools sharp so they remain efficient.
Making sure equipment is well maintained.
Avoiding forcing or gripping the tool more than is necessary.
Wearing gloves to protect the hands.
Exercising and massaging the fingers during breaks to restore circulation.

Health surveillance is crucial to spot and respond to early signs of damage.

Dangers of Vibration at Work – Further Reading

Chapter 2 of Part 5 and Schedule 6 to the Safety, Health and Welfare at Work (General Application) Regulations 2007 (S.I. No. 299 of 2007) as amended by the Safety, Health and Welfare at Work (General Application) (Amended) Regulations 2007 (S.I. No. 732 of 2007) sets down the minimum requirements for the protection of workers from the health risks associated with vibration in the workplace. This is a legislation that looks into dangers of vibration at work.

The Health and Safety Authority of Ireland (HSA) on their webpage Vibration at Work provide relevant to vibration at work information.

Online Health and Safety Training

This is why we have established Myelearsafety school. We pride ourselves in how we guide, support and mentor our students. They receive support throughout their learning experience and into their working lives. Our staff have extensive training experience and also have many years industry experience. We understand the challenges that exist within Environmental and Occupational Health and Safety. Our priority is to ensure that all learners are fully prepared to differentiate themselves in the workplace after completing our Health and Safety courses.

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Working at Height

Working at height and falling from height is one of the biggest causes of death in the workplace and one of the main causes of major injury. Such injuries do not necessarily involve falls from very high scaffolding. They can be caused by any fall above or even below ground level such as an access ladder to an inspection chamber or sewer.

Working at Height Hazards

There are many hazards associated with working at height. The most common hazards include:

Using stepladders or unsuitable alternatives such as chairs or climbing on racking.
Working on scaffolding and other access equipment with inadequate fall arrest controls.
Falling through fragile roofs or skylights.
Objects such as tools falling from height and injuring those below.

Preventing Working at Height Accidents

Preventing working at height accidents is important on many levels. It can avoid costly legal costs but more importantly it can prevent human suffering and in the worst case scenario – human fatality. Preventing accidents is everyone’s duty, from employer to employee. Accidents most often occur:

People taking shortcuts and not using the correct equipment.
Equipment is not available or in poor repair.
Complacency, perhaps over-familiarity with the job.
Lack of awareness of the risks of working at height.
Inadequate training and supervision.

Managing and Selecting Equipment for Working at Height

There are a few simple – but important steps:

Carry out a risk assessment of tasks that are at height. Include in the risk assessment any fragile surfaces that might break if someone worked on it or fell onto it, e.g. fibre and asbestos cement roof sheets and skylights.
If at all possible, avoid working at height and consider if the task can be done in another way, for example using a sponge on an extendable pole to clean windows instead of climbing a ladder.
If working at height cannot be avoided, use equipment or other measures to prevent falls, e.g. guard rails, work platforms, podium steps, tower scaffolds, cherry pickers or scissor lifts.
When the risk of a fall cannot be eliminated, use equipment or other measures to minimise the distance and consequences of a fall, e.g. harnesses, netting and airbags.
Avoid working on, near, or passing across, fragile surfaces, e.g. repair skylights form underneath or provide fixed walkways with guard rails.

Additional measures to reduce the risk of a fall when using equipment for working at height include making sure:

The people have been trained to use it safely.
It is well maintained and regularly inspected.
There is adequate supervision to ensure people are working safely.

Working at Height – Ladders

Ladders are working at height equipment. Ladders may be suitable for light tasks of short duration, but suitable alternatives should be first considered. If ladders have been selected there are a few basic points to remember:

Always check ladders for damage before use.
Set them at the correct angle. The angle should be about 75° or the 1 in 4 rule, i.e., 1 unit out for every 4 units up. If they are at too steep an angle, the ladder could topple backwards and if too shallow an angle, it might slide down the wall.
The ladders must be secure. The ladders should be on firm, level, non-slippery ground. Ladders should not be leaned against plastic guttering. Ladders should always lean against a firm and resistant resting point.
Always grip the ladder and face the rungs when climbing. Try to avoid holding items when climbing but if you do need to carry something, have one free to grip the ladder.
Do not overreach. Keep your belt buckle within the stiles.
Keep both feet on the same rung throughout the task and don’t use the top 3 rungs of the ladder as this prevents a handhold.

Available Resources

The Health and Safety Authority of Ireland (HSA) has published a number of useful resources in relation to Working at Height. Some of these are:

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

True Cost of Poor Workplace Safety

True cost of poor workplace safety can be significant and very harmful to everyone interacting with the business with poorly managed Health and Safety. It can be a reason for significant business costs. More importantly, it can have distressing human costs.

Implementing and managing Health and Safety procedures in the workplace is not an optional addon to regular business activity. It is a legal requirement. It is also a moral and ethical obligation. Excuses, such as ‘health and safety is not necessary in our case’, ‘it’s just bureaucracy and unnecessary paperwork’ and ‘we don’t need it – we know what we are doing’ are not acceptable. All workplaces should strive to achieve a workplace which is a safe workplace as much as it is feasible. All work related injuries should be brought as close to zero as possible.

It is sometimes that employees themselves approach Health and Safety procedures lightly. Even if warned about dangers, they might abandon correct Health and Safety procedures to ‘speed up’ or avoid doing ‘extra work’. This is often guided by the misconception that they will be able ‘to see’ if anything dangerous starts developing and adjust themselves to avoid disaster’ – which is almost never true. In fact, danger started to develop the moment Health and Safety policies were ignored.

The Ultimate Price of Poor Workplace Safety

There is no such a thing as ‘light’ work-related injury. All injuries can take a heavy toll to everyone involved. Unfortunately, some injuries could be fatal. Sadly, this is the ultimate true cost of poor workplace safety.

In 2022 there were 26 workplace related fatalities in Ireland. 26 people left their home, their families never to return home. You can read more about Workplace Fatalities from 2017 to 2022 in our blog entry from 30th June 2023 Health and Safety in the Workplace.

Workplace accidents and their prevention are key priorities of anyone at work. This is not only true for employers but employees as well. You can read more about Workplace Accidents and Their Prevention in our blog entry Health and Safety in the Workplace from 21st April 2023.

From the PRESS

The following contains few of countless examples that demonstrate true cost of poor workplace safety:

Man, 20s, dies in Carlow road tragedy after reportedly falling from truck

A man in his 20s has died following a road traffic accident in Carlow when he reportedly fell from a truck.

The tragic incident took place in the College Green area of Carlow town on 16th August 2023 at 1:30pm on Wednesday afternoon.

Gardaí are investigating the circumstances of the man’s death to determine the exact cause.

A spokesperson for An Garda Síochána told The Irish Mirror: “It’s reported that a male in his 20s received fatal injuries after falling from a truck during the course of his work.

Taken from The Independent.

Male worker, 26, dies after suffering ‘severe head injuries’ in ‘heavy machinery incident’ at construction site of Everton’s new stadium – the football club says everyone is ‘heartbroken’ by the death as investigation is launched (UK)

A 26-year-old construction worker has died after suffering ‘severe head injuries’ in an incident at site of Everton’s new stadium.

First responders were called to the site at Bramley Moore Dock around 12.32pm on 14th August 2023 following a ‘major incident’ that allegedly involved heavy machinery.

The worker was rushed to hospital but despite medics’ best efforts, he died.

Construction company Laing O’Rourke confirmed to MailOnline the man was carrying out work at the time of his death as Everton FC described the news as ‘heartbreaking’.

Investigators with Merseyside Police and the Health and Safety Executive (HSE) remain at the scene as they ‘continue with the early stages of the investigation’.

Workers from the site at Bramley Moore Dock said they were informed of the incident and then asked to leave the area, but couldn’t share more details, The Liverpool Echo reported.

Local reports indicate the incident involved heavy machinery and the 26-year-old suffered head injuries.

Taken from The Guardian.

Farm Safety Week 2020 – Elizabeth’s story

Elizabeth Ormiston, a beef farmer from Co. Cavan suffered a farm accident in 2009 that resulted in her being placed in an induced coma. This is her story.

Farm Safety Week 2020 – Elizabeth’s story (YouTube Link). Run time 2m 19s.

Managing Health and Safety in the Workplace

The role of the Health and Safety Authority of Ireland (HSA) has an important role as they ensure that over 2 million workers (employed and self-employed) and those affected by work activity are protected from work related injury and ill-health. The Health and Safety Authority strategic priorities are to:

Regulate: Increase focus on compliance through risk based inspection and enforcement.
Promote: Support, educate and raise awareness to prevent accidents, injuries and ill health.
Accredit: Grow the national accreditation service to enable and support enterprises and public services.
Influence: Partner and collaborate in support of healthy, safe and productive lives and enterprises.

All workplaces, from one-person farms to multinationals with thousands of employees must implement Health and Safety procedures guided by legislation and best work practices.

The HSA exists to assist and support achieving a safe workplace. This support is available to employers and employees equally.

Don’t Become a Statistic!

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Noise at Work

Often wrongly disregarded as trivial, noise at work could have a severe impact on human health. Any unwanted sound around us, or loud discordant or disagreeable sound or sounds can be referred to as noise. While low levels of noise in the workplace are unlikely to cause harm, louder levels of noise can result in permanent hearing damage or loss.

Legislation in Relation to Noise at Work

The General Application Regulations 2007, Chapter 1 of Part 5: Control Of Noise at Work is available legislation to protect workers from noise exposure. This legislation sets down the minimum requirements for the protection of workers from the health risks associated with noise in the workplace.

In addition, the Health and Safety Authority of Ireland has published Noise related FAQ on their website. This is a sound source of information for most Noise related questions.

Signs of Excessive Noise at Work

The effects of very loud noises are often instantly apparent, but damage caused through exposure to lower levels of sound over a longer period of time may initially go unnoticed.

Generally speaking, a person is exposed to excessive levels of noise when:

They have to shout to be clearly heard by someone 2 meters away.
Their ears are still ringing after leaving the workplace.
The noise is intrusive (e.g. a vacuum cleaner) for most of the day.
They work in a noisy industry (e.g. construction).
There are noises due to impacts such as caused by hammering.

Symptoms of Hearing Damage

Noise is measured in decibels (dB). Environments of 80 dB or more require employers to carry out a noise risk assessment and control methods should be introduced, such as providing information, training and hearing protection. If noise levels are above 85 dB, hearing protection zones should be established and PPE provided to anyone needing to enter a hearing protection zone.

Some of the symptoms of hearing damage are:

Temporary hearing loss after exposure to loud noise.
Ringing or noises in the ears (tinnitus).
Difficulty is distinguishing similar sounding words.
Muffled sounds.
Background noises making conversation confusing.
Having to ask people to speak louder or increase the volume on TVs and radios.

Selecting PPE for protecting against Noise at Work

When selecting PPE, it is important to make sure that the equipment is:

selected carefully with sufficient rating for the noise hazard,
fitted correctly,
compatible with other PPE used by the workforce,
properly maintained,
worn whenever it is appropriate.

In noise control areas, fire alarms must be supplemented with flashing lights or beacons. In the interest of safety, the wearing of hearing defenders outside the restricted area should be discouraged to make sure employees are aware of sounds around them.

Levels of Noise at Work Control

The Noise at Work control levels are:

1. Identify the hazard and assess the risk. This requires a specialist assessment using a noise meter.

2. Reduce the noise by:

designing systems with low levels of noise,
choosing machines with lower levels of noise,
enclosing equipment in sound proofing material,
lagging noisy ducting and pipes,
adding acoustic dampening panels on walls and ceilings,
having equipment properly and regularly maintained.

3. Reduce exposure to personnel (can the regular job be performed further away from the noise source).

4. Reduce the time the employee is exposed to noise.

5. Mark areas where there is a noise hazard as designated areas of protection.

6. As a last resort, if noise is unavoidable, provide Personal Protective Equipment (PPE) and organise proper training in its use.

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie

Health and Safety in the Workplace

Effective Health and Safety management in the workplace is an important element of every organisation. Every year, accidents at work cost the Irish industry billions of euros. The effects of the injuries sustained vary from minor to major injuries. In some cases, employees will be needing an extended period of time off work. In other cases they will never be able to work again. Unfortunately, in some cases they will receive injuries that would be fatal. The fact is, many of these accidents are avoidable and should have not happened.

Much of Health and Safety relies on ensuring that the appropriate risk precautions are in place. Additional information about workplace hazards are available in our blog entry from 21 April 2023 Workplace Accidents and Their Prevention. If individuals are aware of potential hazards and adopt safe working practices, they can control the risks and reduce the number of accidents and injuries.

Workplace Fatalities from 2017 to 2022

The work-related injuries include any injuries incurred by workers in the course of their work. These injuries can range from minor injuries to the most serious injuries that resulted in death. According to the Health and Safety Authority of Ireland and the Health and Safety Statistics they publish, the following is workplace fatalities statistics for years 2017 – 2022:

2017 – 47 fatalities.
2018 – 39 fatalities.
2019 – 48 fatalities.
2020 – 54 fatalities.
2021 – 38 fatalities.
2022 – 26 fatalities.

There have been 230 fatalities in Ireland since 2017.

Health and Safety in the workplace is an important aspect of any organisation. All work related fatalities are preventable through vigilance and effective Health and Safety management. All employees and persons affected by business activities deserve to go home after their work day has ended.

Common Causes of Accidents in the Workplace

Whilst not all workplace accidents result in death, the majority of them will result in an injury. Common causes of accident in the workplace are often:

Slips, trips and falls.
Poor lifting and carrying.
Being struck by vehicles or moving objects.
Falls from height.
Misuse of machinery.
Incorrect use of harmful substances.

Work related activities can also be responsible for diseases and ill health. These, in some cases, can have long term, irreversible effects. For example:

Hearing loss from noisy workplaces.
Stress
Skin disorders.
Hand Arm Vibration Syndrome (HAVS).
Back pain.
Asbestosis and cancer as a result of asbestos exposure.
Work-related lung diseases and cancers.

These hazards can be controlled by assessing risks and putting in effective controls. Effective health and Safety practices will not only minimise the pain and personal consequences to individual employees, but also reduce the financial impact on employers and services funded by the taxpayer.

Business and Human Costs of Ineffective Health and Safety in the Workplace

The costs on the business for ineffective Health and Safety in the Workplace can be significant:

Legal advice and insurance costs.
Legal action, possibly resulting in compensation.
Sick pay.
Lost production and sales.
Equipment and stock losses and damage.
Time and money spent on investigations and improvements.
Recruitment and payment of cover/replacement staff.

These, however, can fade into insignificance when weighed against the human cost:

Pain and suffering.
Disability, possibly long-term.
Health care and rehabilitation.
Loss of earnings.
emotional and financial burden on family.
Potential loss of life.

Safe working conditions are a prerequisite for a healthy and productive workforce.

Ineffective Health and Safety in the Workplace – From the Press

The Health and Safety Authority reported on 26th June 2023 that the company was fined €750,000 after fatal fall from height in workplace. The fatal incident occurred when a worker stepped onto a fragile surface. The fragile surface that sealed a vertical service duct which gave way and the worker fell from a height.

Mark Cullen, Assistant Chief Executive of the Health and Safety Authority, commented, “Where there is a known risk in a workplace, in this case working from height, employers in control of that workplace have a duty to ensure that the appropriate precautions are in place. This will protect employees and others who may be carrying out work activity at the place of work under their control. Failure by the employer in this case has led to the tragic death of a worker. We urge employers to carry out risk assessments and engage with their employees and others to ensure that incidents like this one are prevented.”

Online Health and Safety Training

Myelearnsafety offers fully online Health and Safety courses.

To find out more, please check our Courses page.

Alternatively, should you need any additional information, please do not hesitate to let us know via email info@elearn.ie